YB/T 4639-2018 热风炉用红柱石砖/Andalusite bricks for hot blast stove

2024-11-19

热风炉用红柱石砖

1范围

  本标准规定了热风炉用红柱石砖的定义、牌号及形状尺寸、技术要求、试验方法、质量评定程序、包装、标志、运输、储存及质量证明书。

  本标准适用于钢铁行业热风炉用红柱石砖,

2 规范性引用文件

  下列文件对于本文件的应用是必不可少的。凡是注日期的引用文件,仅注日期的版本适用于本文件。凡是不注日期的引用文件,其最新版本(包括所有的修改单)适用于本文件。

  GB/T 2992.1 耐火砖形状尺寸 第1部分:通用砖

  GB/T 2997致密定形耐火制品体积密度、显气孔率和真气孔率试验方法

  GB/T 5072耐火材料常温耐压强度试验方法

  GB/T 5073耐火材料压蠕变试验方法

  GB/T 5988耐火材料加热永久线变化试验方法

  GB/T 6900铝硅系耐火材料化学分析方法

  GB/T 7321定形耐火制品试样制备方法

  GB/T 10325定形耐火制品验收抽样检验规则

  GB/T 10326定形耐火制品尺寸、外观及断面的检查方法

  GB/T 16546定形耐火制品包装、标志、运输和储存

  GB/T 21114耐火材料 X射线荧光光谱化学分析 熔铸玻璃片法

  GB/T 30873 耐火材料抗热震性试验方法

  YB/T 370 耐火材料荷重软化温度试验方法(非示差-升温法)

  YB/T 5012?高炉及热风炉用耐火砖形状及尺寸

3定义

  下列术语和定义适用于本文件。

3.1

  热风炉用红柱石砖 andalusite bricks for hot blast stove

  热风炉用红柱石砖是指以天然红柱石为主要原料的烧成制品。

4 牌号及形状尺寸

4.1 热风炉用红柱石砖按理化指标分为:RH-155、RH-150、RH-145、RH-140、RH-135、RH-130 六个牌号。其中 R和 H 分别是“热风炉”“红柱石”的首个汉字的汉语拼音首字母,后面的数字为蠕变率试验温度的 1/10。

4.2 砖的形状尺寸应符合 GB/T 2992.1、YB/T 5012的规定,也可按需方提供的图纸进行生产。

5 技术要求

5.1 热风炉用红柱石砖的理化指标应符合表1的规定。

表1 热风炉用红柱石砖的理化指标

项目

指 标

RH-155

RH-150

RH-145

RH-140

RH-135

RH-130

w(A2lO3,)/%

μ0≥

69

65

61

57

53

49

σ

1.5

w(Fe2O3,)/%

μ0≤

1.0

1.0

1.2

1.2

1.5

1.5

σ

0.1

w(TiO2)/%

μ0≤

0.5

0.5

0.5

0.6

0.6

0.6

σ

0.1

显气孔率/%

μ0≤

20(22)

20(22)

20(22)

20(22)

20(22)

20(22)

σ

1.5

体积密度a/(g/cm3)

2.55~2.70(2.50~2.65)

2.50~2.65(2.45~2.60)

2.45~2.60(2.40~2.55)

2.40~2.55(2.35~2.50)

2.35~2.50(2.30~2.45)

2.30~2.45(2.25~2.40)

耐压强度b/MPa

μ0≥

55(50)

55(50)

50(45)

50(45)

40(35)

40(35)

Xmin

45

45

40

40

30

30

σ

15

15

12

12

10

10

0.2 MPa 荷重软化温度
T0.6/℃

μ0≥

1700

1700

1650

1600

1520

1450

σ

10

15

加热永久线变化/%

(1500℃X2 h)±0.2

(1500℃x2 h)±0.2

(1500℃X2 h)±0.2

(1450 ℃X2 h)±0.2

(1450℃X2 h)±0.2

(1450℃X2 h)±0.2

蠕变率(0.2 MPa,0~50 h)/%

μ0≤

0.8
(1550℃)

0.8
(1500℃)

0.8
(1450℃)  

0.8

(1400℃)

0.8

(1350℃)

0.8
(1300℃)

σ

0.1

注1:括号内为格子砖或手工砖的指标。

注2:抗热震性可根据用户需求进行检测。

a体积密度为设计用砖的参考指标。
b耐压强度所测单值均应大于Xmin规定值。

 

表2墙砖的尺寸允许偏差及外观 单位为毫米

项 目

指 标

尺寸允许偏差ª

尺寸≤150

±2

尺寸151~345

±3

尺寸>345

±4

扭曲

长度≤300

不大于

1.0

长度>300

2.0

缺角长度(a+b+c)

40

缺棱长度(e+f+g)

50

熔洞直径

工作面

6

非工作面

8

裂纹长度

宽度≤0.25

不限制

宽度0.26~0.5

50

宽度>0.5

不准有

厚度相对边差

1

楔度差

1

层裂

不准有

a根据用户需求可对砖的一个主要尺寸进行分档。

 

表3 格子砖的尺寸允许偏差及外观

项 目

指 标

尺寸允许偏差a

长度(宽度)

+1

-3

高度(厚度)

±2

同一面上相邻的间距

±1

厚度相对边差

1

缺角缺棱长度(a+b+c)、(e+f+g)

40

熔洞直径

工作面

6

非工作面

8

裂纹长度

宽度≤0.25

不限制

宽度0.26~0.5

30

宽度>0.5

不准有

a高度(厚度)应根据顾客要求进行尺寸分档;长度(宽度)≥250及高度(厚度)≥150时,尺寸允许偏差供需双方协商。

5.2热风炉用红柱石砖的尺寸允许偏差及外观应符合表2和表3的规定。

5.3单重大于 18 kg或难于机械成型的砖,其技术要求参照本标准由供需双方协议确定。

6试验方法

6.1砖的制样按 GB/T 7321进行。

6.2化学成分的测定按GB/T 6900或者GB/T 21114进行。

6.3体积密度和显气孔率的测定按GB/T 2997进行。

6.4常温耐压强度的测定按GB/T 5072进行。

6.5荷重软化温度的测定按YB/T 370进行。

6.6加热永久线变化的测定按GB/T 5988进行。

6.7蠕变率的测定按GB/T 5073进行。

6.8抗热震性的测定按GB/T 30873进行。

6.9砖的尺寸、外观及断面的检査按GB/T 10326进行。

7质量评定程序

7.1组批

  按牌号进行编批,每批不大于300t.

7.2 抽样及合格判定规则

  砖的抽样及验收按GB/T 10325进行。Al2O3,含量、TiO2,含量、显气孔率、常温耐压强度及蠕变率为验收检验项目。

7.3 合格评定形式

  合格评定可采用供货方声明、使用方认定或第三方认证的形式进行。

8 包装、标志、运输、储存及质量证明书

8.1砖采用托盘或根据用户要求进行包装,

8.2砖的运输和储存按GB/T 16546进行,

8.3 砖发出时应附有供方质量部门签发的质量证明书,载明供方名称或厂标、需方名称、发货日期、合同号、标准编号、产品名称、牌号、砖号、批号及相应的理化检验结果等。

 

 

 

Andalusite bricks for hot blast stove

1 Range

  This standard specifies the definition, grade, shape and size, technical requirements, test methods, quality assessment procedures, packaging, marking, transportation, storage and quality certificate of andalusite bricks for hot blast furnaces.

  This standard is applicable to andalusite bricks for hot blast furnaces in iron and steel industry.

2 Normative reference documents

  The following documents are essential for the application of this document. For dated references, the date-only version applies to this document. For undated references, the latest version (including all amendment orders) applies to this document.

  GB/T 2992.1 Shape and dimensions of refractory bricks – Part 1: general purpose bricks

  Test method for bulk density, apparent porosity and true porosity of GB/T 2997 compact shaped refractory products

  GB/T 5072 refractories – normal temperature compressive strength test method

  GB/T 5073 refractories compressive creep test method

  GB/T 5988 refractory heating permanent line change test method

  GB/T 6900 aluminum-silicon refractory chemical analysis method

  GB/T 7321 shaped refractory product sample preparation method

  GB/T 10325 shaped refractory products acceptance sampling inspection rules

  GB/T 10326 shaped refractory products size, appearance and section inspection method

  GB/T 16546 shaped refractory products packaging, marking, transportation and storage

  GB/T 21114 refractories by X-ray fluorescence spectrochemical analysis of fused cast glass sheets

  Test method for thermal shock resistance of GB/T 30873 refractories

  Test method for load softening temperature of YB/T 370 refractories (non-differential warming method)

  YB/T 5012? Shape and dimensions of firebricks for blast furnaces and hot blast furnaces

3 Definitions

  The following terms and definitions apply to this document.

3.1

  Andalusite bricks for hot blast stove

  Andalusite brick for hot blast furnace refers to the fired product with natural andalusite as the main raw material.

4 Grade and shape size

4.1 andalusite bricks for hot blast furnaces are divided into :RH-155, RH-150, RH-145, RH-140, RH-135, RH-130 six grades according to physical and chemical indexes. Where R and H are the Chinese pinyin initial letter of the first Chinese character of “hot blast furnace” and “andalusite” respectively, the number behind is 1/10 of the creep rate test temperature.

4.2 The shape and size of the bricks shall comply with the provisions of GB/T 2992.1 and YB/T 5012, and can also be produced according to the drawings provided by the demander.

5 Technical Requirements

5.1 The physical and chemical indexes of andalusite bricks for hot blast furnaces shall comply with the provisions of Table 1.

Table 1 Physical and chemical indexes of andalusite bricks for hot blast furnaces

Item

Index

RH-155

RH-150

RH-145

RH-140

RH-135

RH-130

w(A2lO3,)/%

μ0≥

69

65

61

57

53

49

σ

1.5

w(Fe2O3,)/%

μ0≤

1.0

1.0

1.2

1.2

1.5

1.5

σ

0.1

w(TiO2)/%

μ0≤

0.5

0.5

0.5

0.6

0.6

0.6

σ

0.1

Apparent porosity/%

μ0≤

20(22)

20(22)

20(22)

20(22)

20(22)

20(22)

σ

1.5

Bulk densitya/(g/cm3)

2.55~2.70(2.50~2.65)

2.50~2.65(2.45~2.60)

2.45~2.60(2.40~2.55)

2.40~2.55(2.35~2.50)

2.35~2.50(2.30~2.45)

2.30~2.45(2.25~2.40)

Compressive strengthb/MPa

μ0≥

55(50)

55(50)

50(45)

50(45)

40(35)

40(35)

Xmin

45

45

40

40

30

30

σ

15

15

12

12

10

10

0.2 MPa load softening temperature
T0.6/℃

μ0≥

1700

1700

1650

1600

1520

1450

σ

10

15

Heating permanent line change/%

(1500℃X2 h)±0.2

(1500℃x2 h)±0.2

(1500℃X2 h)±0.2

(1450 ℃X2 h)±0.2

(1450℃X2 h)±0.2

(1450℃X2 h)±0.2

Creep rate(0.2 MPa,0~50 h)/%

μ0≤

0.8
(1550℃)

0.8
(1500℃)

0.8
(1450℃)  

0.8

(1400℃)

0.8

(1350℃)

0.8
(1300℃)

σ

0.1

Note 1: In parentheses are indicators of lattice bricks or handmade bricks.

Note 2: Thermal shock resistance can be tested according to user requirements.

aThe volume density is the reference index of bricks used in design.
bThe single value of compressive strength measured should be greater than the specified value of Xmin。

 

Table 2 Size tolerance and appearance of wall tiles  Unit in millimeter

Item

Index

Allowable deviation of dimensionª

Dimension≤150

±2

Dimension151~345

±3

Dimension>345

±4

Contort

Length≤300

Not more than

1.0

Length>300

2.0

Missing Angle length(a+b+c)

40

Missing edge length(e+f+g)

50

Hole diameter

Working face

6

Non-working face

8

Crack length

Breadth≤0.25

No limit

Breadth0.26~0.5

50

Breadth>0.5

Be forbidden from

Thickness relative to edge difference

1

Wedge difference

1

Slabbing

Be forbidden from

a A main size of the brick can be graded according to user requirements.

 

 

Table 3 Size tolerance and appearance of lattice bricks    Unit in millimeter

Item

Index

Allowable deviation of dimensiona

Length (width)

+1

-3

Height (thickness)

±2

The spacing of adjacent Spaces on the same surface

±1

Thickness relative to edge difference

1

Missing Angle length (a+b+c), (e+f+g)

40

Hole diameter

Working face

6

Non-working face

8

Crack length

Breadth≤0.25

No limit

Breadth0.26~0.5

30

Breadth>0.5

Be forbidden from

a Height (thickness) should be graded according to customer requirements; When the length (width) is ≥250 and the height (thickness) is ≥150, the size allows the deviation between the supply and demand parties to negotiate.

 

5.2 The size permissible deviation and appearance of andalusite bricks for hot blast furnaces shall comply with the provisions of Table 2 and Table 3.

5.3 For bricks weighing more than 18 kg or difficult to form mechanically, the technical requirements shall be determined by agreement between the supply and demand parties by reference to this standard.

6 Test methods

6.1 Brick sample preparation is carried out according to GB/T 7321.

6.2 Chemical composition shall be determined according to GB/T 6900 or GB/T 21114.

6.3 The bulk density and apparent porosity were measured according to GB/T 2997.

6.4 The compressive strength at room temperature shall be measured according to GB/T 5072.

6.5 The load softening temperature was measured according to YB/T 370.

6.6 The determination of permanent line change of heating was carried out according to GB/T 5988.

6.7 The creep rate was measured in GB/T 5073.

6.8 Thermal shock resistance is measured according to GB/T 30873.

6.9 The inspection of size, appearance and section of bricks shall be carried out according to GB/T 10326.

7 Quality assessment procedures

7.1 Batch

  Batch according to the grade, each batch is not more than 300 t.

7.2 Rules for sampling and conformity determination

  Sampling and acceptance of bricks shall be carried out according to GB/T 10325. Al2O3, content, TiO2, content, apparent porosity, compressive strength at room temperature and creep rate are the acceptance test items.

7.3 Form of conformity assessment

  The conformity assessment can be made in the form of the supplier’s declaration, the user’s certification or the third party’s certification.

8 Packing, marking, transportation, storage and quality certificate

8.1 The bricks shall be packed in pallets or according to user requirements.

8.2 Bricks are transported and stored in GB/T 16546,

8.3 When the bricks are issued, the quality certificate issued by the quality department of the supplier shall be attached, indicating the name of the supplier or factory mark, the name of the demander, the date of delivery, the contract number, the standard number, the product name, the brand number, the brick number, the lot number and the corresponding physical and chemical inspection results.